Sspc Sp 16 PDF
steel SSPC-SP 10 or SP 6 concrete ASTM D4259 or D4260 Method Airlessorconventionalspray Mixingratio(byvolume) 4partsComponentAto1part C omp ne tB ... Page1of3 SSPC-16(C-200A)PDS/AI(2-10) SSPC-16 (C-200A) Coal-tarepoxy Amercoat. ApplicationProcedure 1.
SSPC Definitions SSPC-SP 1, Solvent Cleaning Solvent cleaning is a method for removing all visible oil, grease, soil, drawing and cutting compounds, and other
SSPC-SP-8 Pickling - Removal of all mill scale, rust and rust scale by chemical reaction, or by electrolysis, or by both. It is intended that the pickled surface shall be completely free of
SSPC-SP 16, Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels and Non-Ferrous Metals •Not for carbon steel •Requires sweep blasting the entire surface to remove all foreign matter; paint may remain if it is tightly adherent
3/5/2006 3 SSPC-SP 1- Solvent Cleaning • A method for removing all visible oil, grease, soil, drawing and cutting compounds, and other soluble contaminants from steel surfaces.
SSPC-SP13 / NACE 6 Surface Preparation of Concrete Provides requirements for surface preparation of concrete by mechanical, chemical, or thermal methods prior to the application of bonded protective coating or lining systems.
with a fine abrasive in accordance with SSPC SP-16 guidelines to achieve a profile of 1.5-3.0 mils. When light abrasive blasting is not possible, galvanizing can be treated with a suitable zinc phosphate conversion coating. Galvanizing that has at
• SSPC-SP COM Surface Preparation Commentary for Steel and Concrete Substrates • Guide to SSPC-VIS 1 Guide and ... • SSPC-SP 16 Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals
Recently Published SSPC Standards • SSPC-AB 4 Encapsulated Abrasive Media issued October 2009 • SSPC-SP 16, Brush-off Blast Cleaning of Coated
SSPC SSPC-SP-5 1.1 A white Metal Blast Cleaned surface, when viewed without magnification, shall be free of all visible oil, grease, dirt, dust, mill scale, rust, paint, oxides,
Solvent Cleaning SSPC-SP1 Definition: Solvents such as water, mineral spirits, xylol, toluol etc., are used to remove solvent-soluble foreign matter from the surface of ferrous metals.
• SSPC-SP 16 Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals • Guide for Selecting One-Coat Shop Painting SystemsGuide to SSPC-VIS 1 Guide and Reference Photographs for Steel Surfaces Prepared by Dry ...
Surface Preparation MINIMAL PREPARATION For coatings requiring only minimal surface preparation, the surface needs to be prepared in accordance to SSPC-SP 1 and SSPC-SP 2 or SSPC-SP 3.
surface preparation shall be in accordance with SSPC-SP 16 of 2.5. Non-ferrous piping one inch in diameter or less shall not be preserved or painted. Surface profile is not required. 3.1.5 For surface ships, pre-construction primer may be retained and
USACE / NAVFAC / AFCEC / NASA UFGS-09 97 13.16 (May 2011)-----Preparing Activity: NAVFAC Superseding UFGS-09 97 13.16 (February 2010) UNIFIED FACILITIES ... SSPC SP 1 (1982; E 2004) Solvent Cleaning SSPC SP 10/NACE No. 2 (2007) Near-White Blast Cleaning
SSPC . Sept 16-19, 2013 – NSRP Fall 2013 . Bath ME . Learning Objectives • Standards Update • CAS Update • Training Course Update . ... (SSPC-SP 11) & Commercial Grade Power Tool Cleaning (SSPC-SP 15) • Field Methods for Extraction and Analysis of
SSPC-SP-6 - COMMERCIAL BLAST CLEANING..... 20 . BLASTING & COATING SAFETY S.E.A.L. International II SSPC-SP ... Abrasive particles larger than 16 to 18 mesh may gouge the metal surface and thus have a slow cleaning rate. However, fine particles ...
... 16:46 PM/22/08 1:16:46 PM. Surface Preparation ... For complete instructions, refer to Joint Surface Preparation Standard SSPC-SP13/NACE 6. SSPC/NACE Standards B SP-5 B SP-10 B SP-6 B SP-7 Rust Grade B 0080206_PMP_Surface 280206_PMP_Surface 2 11/22/08 1:17:05 PM/22/08 1:17:05 PM. Title:
560 COATING NEW STRUCTURAL STEEL. (REV 1-16-13) (FA 2-1-13) (7-13) SUBARTICLE 560-2.4 (Page 743) is deleted and the following substituted: 560-2.4 Soluble Salts Test Kit: Use a soluble salts test kit in accordance with SSPC-
NACE #2 SSPC-SP 10-63T Near White Blast Cleaning. Near white blast cleaned surface finish. Defined as a surface from which all oil, grease, dirt, ... Use clean, dry 16 - 30 mesh abrasive (or a maximum particle size no larger than passing through 16 mesh screen U. S. Sieve Series).
Research News The Effects of Abrasives on Coating Performance: SSPC’s PACE Alternate Surface Preparation Branch By S.K. Boocock Steel Structures Painting Council
570.70-----16 Localized Paint Removal From Structural Steel By Vacuum Contained ... SSPC SP-11 and shall exhibit a suitable anchor profile for the primer paint. ... One bound copy of Steel Structures Painting Council specification SSPC AB-3 Specification for
SSPC SP-3 Power Tool Cleaning: Power tool cleaning is a method of preparing steel surfaces through the use of power assisted hand tools. Power tool cleaning removes all loose mill scale, loose rust,
SSPC – The Society of Protective Coatings SOUTHERN CALIFORNIA CHAPTER (2004 Chapter of the Year) 2004-2005 Board CHAIRMAN JUNE MEETING NOTICE Girth Weld and Pipeline Rehabilitation Coatings
Speciﬁ cation SSPC-SP 16 must be followed obtaining a surface proﬁ le of minimum 1.5 mils (38 microns). Optimum surface proﬁ le will not exceed 2.0 mils (50 microns). Surface Preparation Standards Condition of Surface ISO 8501-1 BS7079:A1
Speciﬁ cation SSPC-SP 16 must be followed obtaining a surface proﬁ le of minimum 1.5 mils (38 microns). Optimum surface proﬁ le will not exceed 2.0 mils (50 microns). Previously Painted Surfaces If in sound condition, clean the surface of all foreign material.
The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 16 (SSPC-SP 16), 2010, Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals .
• SSPC Paint 16-91T Specification For use over prepared substrates such as steel and concrete ... SSPC-SP 7 to provide a 2 mil profile. Concrete/Masonry, Atmospheric Service: New For surface preparation, refer to SSPC-SP13/NACE 6. Surface must
with a fine abrasive in accordance with SSPC SP-16 guidelines to achieve a profile of 1.5-3.0 mils. When light abrasive blasting is not possible, galvanizing can be treated with a suitable zinc phosphate conversion coating. Galvanizing that has at least 12
BILGES to be used in conjunction with CORE PPI 63101-000 with a Cleanliness Level of SSPC-SP-11 (Minimum) Surface Preperation; BILGES; SSPC-SP-11 (Minimum); Surface Preparation; MEDIUM DURABILITY; BILGES; Cleaning; ... 12/2/2005 2:16:43 PM ...
B. SSPC-SP 1 - Solvent Cleaning. C. SSPC-SP 2 - Hand Tool Cleaning. D. SSPC-SP 3 ... 1.3 DEFINITIONS A. Definitions of Painting Terms: ASTM D 16, unless otherwise specified. 1.5 SUBMITTALS A. Comply with Section 01330 - Submittal Procedures.
SSPC SP-3 Power tool cleaning may be authorized for fairing in the spot and sweep surface as required. 2. The contractor shall inspect the existing coating on the hull and shall determine the sequence ... 3/7/2012 8:56:16 AM ...
July 15-16, 2008 Chicago. Casings and Assessments Regulatory Requirements ... • SSPC-SP 3 Power Tool CleaningSP 3 Power Tool Cleaning • SSPC-SP 10/NACE No. 2 Near White Blast Cl iCleaning • SSPC-SP 6/NACE No. 3 Commercial Blast Cleaning
16. SSPC SP 5 - Joint Surface Preparation Standard White Blast Cleaning. 17. SSPC SP 6 - Surface Preparation Specification No. 6 Commercial Blast Cleaning. 18. SSPC SP 10 - Surface Preparation Specification No. 10 Near-White Blast Cleaning. 19.
1.2.5 Section 16 05 00 - Basic Electrical Materials and Methods: Mechanical identification. 1.3 REFERENCES ... 126.96.36.199 SSPC-SP 13/NACE No. 6 Surface Preparation for Concrete. 07/20/11 Issuance UTD – Section 09 90 00 Page 2 of 12
Traditionally for areas where wet or dry abrasive blasting to SSPC-SP 5 or SP 10 was not possible (see Figures 1 and 2) this has meant that a SSPC-SP11 standard utilizing methods such as: 1 Paper No. ... 16 Conditioning at +68ºF (+20ºC)
Exceed requirements of SSPC Paint 16 performance requirements. Performance Data Salt Spray (ASTM B 117) 3000 hours Plane blistering or rusting: none ... Tool cleaning per SSPC-SP 2, Power Tool cleaning per SSPC-SP 3 or High Pressure Water cleaning per SSPC-SP12/NACE 5 WJ-4 is recommended.
The coating shall be coal tar epoxy-polyamide conforming to Steel Structures Painting Council specification SSPC Paint 16; color black. CONSTRUCTION DETAILS ... 1. Solvent Cleaning: Solvent-clean surfaces in accordance with SSPC SP 1. Remove visible oil,
prep: sspc sp-6 field bolts total qty. qty. description length 4 4 7/8"dia a325n bolt 2 1/2" drawn by reviewed by rst ssk date 05/09/2013 date 05/15/2013 job no bm3011 123014 ... bm3011 1 w24x94 24'-1 9/16" 2275 a992 beam sq-2 p3002 3 pl1/4"x1" 0'-9 1/8" 2 a572-gr.50
Surface Preparation: SSPC-SP 6/NACE 3 Primer: Series N69 Hi-Build Epoxoline, DFT 3.0 to 5.0 mils  ... 16 Use Series 218 or 219 as a surfacer, filler or patcher if needed. 17 Series 243 is for vertical application needs in conjunction
Abrasive Blast All structural steel shall be abrasive blast cleaned to an SSPC-SP 10/NACE NO. 2“Near White Metal Blast Cleaning” standard as described in the current SSPC documents.
16 Wood & Drywall: Self-priming or Series 201. CMU & Concrete: Series 216, Series 201 or 273 mixed with fumed silica. ... SSPC-SP 13/NACE 6 Concrete : SSPC-SP 13/NACE 6. ICRI CSP 3-4 Primer: Series 201 Epoxoprime , DFT 6.0 to 8.0 mils.
S3 Steel Immersion Amerlock 2AL SSPC SP-10 4.0-8.0 2 8.0-16.0 S4 Steel Lining Material for ... *SSPC SP-6 is minimum, depending on service conditions. Notes For System G1: New galvanized steel can also be mechanically cleaned, ...
Near White Grade (SSPC-SP-10, NACE 2) with a 2-3 mil (50-75μ) surface profile is recommended for optimal performance. ... Thin as needed up to 16% with 160 Thinner for all air atomized spray applications. AIRLESS SPRAY: Pump Ratio Pump Output Fluid Hose
Publish Date: 09/16/13 www.versaflex.com 913.321.9000 Contact us for your own custom specifications ... SSPC-SP 5 White Metal Blast Cleaning SSPC-SP 10 Near-White Metal Blast Cleaning SSPC-PA 2 Measurement of Dry Coating Thickness with Magnetic Gauges
SSPC-SP 12. All pitted and corroded areas shall be filled and blended to ensure a smooth surface for maximum lining adhesion. Prepare surface to NACE RP0178. SEAMING: ... Microsoft Word - SurfacePreparationSpec 16-23-20.doc Author: diana wydysh
SSPC-SP 16 are acceptable methods Concrete Concrete must be cured 28 days at 24°C (75°F) and RH 50% or equivalent. Prepare surfaces in accordance with ASTM D 4258 Surface Cleaning of Concrete and ASTD D 4259 Abrading Concrete. Voids in concrete
STEEL STRUCTURES PAINTING COUNCIL (SSPC) SSPC-SP-5 - White Metal Blast Cleaning ... SP-5 or SSPC-SP-10, as required (see Steel Structures Painting Council Manual, Volume 2 for more ... (16 oC), preheat booths ...
16. F436 Specification for Hardened Steel Washers B. American Welding Society ... E. Steel Structures Painting Council (SSPC): 1. SSPC-SP 1 Solvent Cleaning 2. SSPC-SP 3 Power Tool Cleaning ... ferrous metalwork in accordance with SSPC-SP 3 to remove mill scale, rust, grease, oil, ...
SSPC-SP 1 Solvent Cleaning 5. SSPC-SP 6/NACE No. 3 Commercial Blast Cleaning 6. SSPC-SP 11 Power Tool Cleaning to Bare Metal 7 ... 11-16. CALIFORNIA HIGH-SPEED TRAIN PROJECT – STANDARD SPECIFICATIONS HIGH-PERFORMANCE COATINGS Date: 08/17/2012 09 96 00 ...