AS6174 (Ref. elements of Section 3) to ensure that Counterfeit Work is not delivered to Buyer. The purpose of Seller’s Plan shall be to develop a robust process to prevent the delivery of counterfeit commodities and control commodities identified as counterfeit .
AS6174 also standardizes practices to assure authenticity and conformance of procured materiel, control materiel identified as fraudulent or counterfeit, and report counterfeit materiel to other potential users and government investigative agencies.
CCAP-101 Registered Service Mark CCAP-101 Copyright 2013 - CTI, Inc. All rights reserved Rev. E-1 7/11/13 Components Technology Institute, Inc. (CTI, Inc.) 904 Bob Wallace Ave., Suite 117, Huntsville, AL 35801 1
AS6174 – similar to AS5553, but applicable to ALL types of materiel used in high performance/high reliability applications with potential appendices for specific commodity areas
A SpeciAl RepoRt counterfeit parts: increasing Awareness and Developing countermeasures March 2011
• AS6174 for counterfeit materials, under development, targeted for high reliability applications. “DMSMS Industry Standard” Representative of Boeing Seattle)( • Targeted for publication as a Tech America standard under the GEIA ...
AS5553 (Electronics) and AS6174 (Material). 4.14 Right of Entry – Representatives of Moog, Moog’s customer, and other regulatory authorities have access to supplier’s and all shall
AS6174 . IV. RESPONSIBILITIES . A. TW Metals: It is the responsibility of TW Metals to provide the subcontractor with product requirements by . specification or other standards. These requirements may be invoked whole or in part by reference
References • SAE AS5553 – Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition • SAE AS6174 – Counterfeit Material; Assuring Acquisition of Authentic and
The requirements of AS6174 Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel are in affect for all material delivered to Crissair. Each supplier shall implement controls to the extent necessary to deliver FOD free product using AS ...
DoD Counterfeit Prevention Framework 6 Example Higher Level Quality Requirements for Combating Counterfeits • AS6174, Counterfeit Materiel; Assuring Acquisition of Authentic and
4.12.13 OEM anti-counterfeit plans including SAE AS5553 and SAE AS6174..... 28 4.13 OEM anti-counterfeit guidelines for their products ..... 28 4.13.1 IP control ...
AS6174 - Counterfeit Material; Detection, Mitigation, and Disposition http://www.sae.org/servlets/works/documentHome.do?comtID=TEAG21&docID=AS6174&inputPage=wIpSdOcDeTaIlS . 4/28/2013 35 G19 SUB COMMITTEE DEFINITION OF COUNTERFEIT
AS6174-Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming • April 20, 2010 – DoD PSMC (Part Standardization and Management Committee) requested SAE to address counterfeit NON-electronic parts • For all applications
pedigree and to determine source of parts. Records can be reviewed to identify parts obtained from potentially unreliable sources of supply, such as uncertified bro-
place in full compliance to AS5553 and AS6174 to detect, and preclude delivery of any counterfeit components or materials from being delivered to RAM. The Supplier shall ensure that only new and authentic materials are used in products delivered to RAM.
DCMA Texas Integrated Staff Assist Visit Risk-Based Surveillance – a Government/Industry Partnership Presented By:
AS6174 is the electronic/ electrical reference for this activity. SAE AS6174 describes the elements needed in a counterfeit materiel control plan, including purchasing processes, purchasing information and material control.
plan in accordance with AS5553 and AS6174. QAP 17 The supplier shall maintain a documented FOD prevention program. The program shall be compliant with National Aerospace Standard NAS-412: Foreign Object Damage/Foreign Object Debris (FOD) Prevention.
AS6174, Assuring Acquisition of Authentic Conforming Material. 4.0 Definitions 4.1 Suspect Part – A part in which there is an indication by visual inspection, testing, or other information indicating the
__ AS6174 Cert Body: Cert No.: QTSL (If applicable) For membership to the following committee check the box and the application will be sent to you. USNC/IECQ . FRM-1021 CAMA Membership Application Rev. 03 Page 2 of 2 Please describe your primary interest in CAMA?
AS6174 (Section 3) to ensure counterfeit materiel is not delivered to West Coast Lockwasher (WCL). • Supplier agrees and shall ensure that counterfeit materiel has not been delivered and shall ensure that only new and authentic materials are used in materiel delivered to
SAE AS6174 Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel Parts and materials 17-Jun-13 X X XXXXXXReleased May 2012 SAE AS6081 Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and
of Section 4) and/or AS6174 (Ref. elements of Section 3) to ensure that Counterfeit Work is not delivered to . Buyer. The purpose of Seller's Plan shall be to develop a robust process to prevent the delivery of counterfeit commodities and control commodities identified as counterfeit.”
supported by AS6174 and AS5553 internally. Counterfeit material compliance is supported by AS6081 for distribution partners. 7 With the presentation slides be available for download after the conference? Yes - the presentation can be downloaded from this web-site: www.ducommun.com
with section 3 of as6174 to prevent the usage of counterfeit parts / materials and assure the acquisition of authentic and conforming materials only. if supplier does not have a documented control plan in place and/or the control plan in
Suppliers should utilize and reference AS6174 for guidance. Suppliers shall also flow down counterfeit parts programs requirements to their sub-tiers, especially but not limited to: Electronic parts suppliers . Supplier Quality Requirements Revision 6/10/13 Page
Meggitt Oregon Purchase Order Quality Notes REV.: 6/4/2013 Page 6 of 6 FORM 86 SAE AS6174. QP-28 Boeing-Defense Owned Tooling
AS6174. In clause #10 added Lockheed document retention requirement per Lockheed specification 5PTPTT11 23 04/19/13 M. Martinez 3 Updated the standard clauses applicable to all purchase order. Added supplier flow down Boeing D6-51991 document . Title ...
SAE AS6174 Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel Parts and materials X X XXXXXXReleased May 2012 SAE AS6081 Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition – Distributors
Suppliers should utilize and reference AS6174 for guidance. Suppliers shall also flow down counterfeit parts programs requirements to their sub-tiers, especially but not limited to: Electronic parts suppliers Raw material suppliers
control plan for counterfeit parts and material using industry standards AS6174 and AS5553 as guidelines. The . STROCO Manufacturing, Inc. VENDOR Terms and Conditions & Quality Clauses KDW030514
accordance with AS5553 and/or AS6174 as applicable to supply only authentic and conforming parts/items purchased from the Original Component Manufacturer (OCM), Original Equipment Manufacturer (OEM) or authorized distributors chain only with a plan to mitigate risk, control,
5553 (Ref. elements of Section 4) and/or AS6174 (Ref. elements of Section 3) to ensure that Counterfeit Work is not delivered to Buyer. • For purposes of this clause, Work consists of those commodities delivered under this Contract that
See AS6174, Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel for guidance CONTACT DESIGN/OL Please submit comments or questions concerning this document to Design/Ol via e-mail to the following address:
AS6174. In clause #10 added Lockheed document retention requirement per Lockheed specification 5PTPTT11 . Title: sSierracin/Sylmar Author: Jim Wickham Created Date:
assure the authenticity and conformance of purchased material per AS6174. Title: Microsoft Word - D-6-1 _Purchase Order Quality Clauses_ Author: poirierj Created Date:
avoidance can be found in SAE documents AS5553 (Electronics) and AS6174 (Material).
AS6174. 5. Revise section ...
• AS6174 Standard, “Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel” • ARP6178 Aerospace Recommended Practice, “Fraudulent/Counterfeit Electronic Parts; Tool for Risk Assessment of Distributors”
Suppliers may utilize AS6174 for guidance. 5.0 RECORDS As described above (18); for a minimum of ten years. 6.0 REFERENCES . 6.1 AS9100, Revision C . 6.2 BP 4.6-1 . 6.3 QP 4.6-2 . Page 6 of 6 . Title: CONTRACT REVIEW Author: Document Control Created Date:
reference to NAS-412 and AS6174 Oct 28, 2013 Issue 13 Added description of Tooling Verification Dec 02,2013 Issue 14 Added a note to Section 1, paragraph I, requesting from supplier that all documentation shipped to Ontic from existing stock/inventory shall have
Seller shall have counterfeit program compliant to AS5553 and/or AS6174. Supplier is REQUIRED to prevent the shipment of counterfeit/suspect unapproved products to ACE. Seller shall immediately notify ACE if it is aware or suspects that it has furnished counterfeit work.
˜Industry standards, such as the SAE AS6081, AS5553 and AS6174 will assist stakeholders in mitigating counterfeit parts, as long as the conformity assessment process is robust and recognized. ˜To that effect, we are working to ensure that any attestation of conformity
AS6174 - Counterfeit Material; Detection, Mitigation and Disposition AS9100 - Aerospace Quality Management Standard AS9120 - Quality Management Standard; Requirements for Aviation’s, Space and Defense Distributors
“AS6174 Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel” should be used as a general guideline in establishing a counterfeit parts prevention program in order to mitigate risks of receiving and installing counterfeit parts.
Parts/Material Program according with the requirements of AS6174 as appropriate to their operations. This program will be available for review and verification by Quality Aluminum Forge upon request. 280. MATERIAL SUBSTITUTION PROHIBITION
Aerospace Standard AS6174 presents a counterfeit materiel risk assessment model based on ¿impact of supply chain¿ (cost of operations, degraded function, sabotage or malicious functions, personnel injury or death) and ¿likelihood of
AS6174 Camel AS6180 Butter cookie AS6183 English green AS6184 Rust AS6188 Charcoal AS6189 It’s red AS6191 Ebony flesh AS6195 Teal AS6197 French vanilla AS6211 Creamy beige AS6216 Medium flesh AS6217 Baby pink S6226 It’s white AS6227 It’s black AS6230 Natural brown AS6231 Waterfall AS6234
AS5553, AS6174, ASXXXX. Written procedures are recommended for full compliance to these requirements. A. Acceptance of financial responsibility - The seller may be liable for remedial costs should any counterfeit materiel be provided.