Analysis and Design of FRP Reinforced Concrete Structures

Title
Contents
Chapter 1. Introduction
1.1. Evolution of FRP Reinforcement
1.2. Review of FRP Composites
1.3. The Importance of the Polymer Matrix
1.3.1. Matrix polymers
1.3.2. Polyester resins
1.3.3. Structural considerations in processing polymer matrix resins
1.3.4. Reinforcing fibers for structural composites
1.3.5. Effects of fiber length on laminate properties
1.3.6. Bonding interphase
1.3.7. Design considerations
1.4. Description of Fibers
1.4.1. Forms of glass fiber reinforcements
1.4.2. Behavior of glass fibers under load
1.4.3. Carbon fibers
1.4.4. Aramid fibers
1.4.5. Other organic fibers
1.4.6. Hybrid reinforcements
1.5. Manufacturing and Processing of Composites
1.5.1. Steps of fabrication scheme
1.5.2. Manufacturing methods
1.6. Sandwich Construction
1.7. Compression Molding
1.8. Multi-Axial Fabric for Structural Components
1.9. Fabrication of Stirrups
1.10. FRP Composites
1.11. FRP Composite Applications
1.12. Composite Mechanics
1.12.1. Laminate terminology
1.12.2. Composite product forms
1.13. Laminates Types and Stacking Sequence
Chapter 2. Material Characteristics of FRP Bars
2.1. Physical and Mechanical Properties
2.2. Physical Properties
2.3. Mechanical Properties and Behavior
2.3.1. Tensile behavior
2.3.2. Compressive behavior
2.3.3. Shear behavior
2.3.4. Bond behavior
2.4. Time-Dependent Behavior
2.4.1. Creep rupture
2.4.2. Fatigue
2.5. Durability
2.6. Recommended Materials and Construction Practices
2.6.1. Strength and modulus grades of FRP bars
2.6.2. Surface geometry, bar sizes, and bar identification
2.7. Construction Practices
2.7.1. Handling and storage of materials
2.7.2. Placement and assembly of materials
2.8. Quality Control and Inspection
Chapter 3. History and Uses of FRP Technology
3.1. FRP Composites in Japan
3.1.1. Development of FRP materials
3.1.2. Development of design methods in Japan
3.1.3. Typical FRP reinforced concrete structures in Japan
3.1.4. FRP for retrofitting and repair
3.1.5. Future uses of FRP
3.1.6. FRP construction activities in Europe
3.2. Reinforced and Prestressed Concrete: Some Applications
3.2.1. Rehabilitation and strengthening
3.2.2. Design guidelines
3.3. FRP Prestressing in the USA
3.3.1. Historical development of FRP tendons
3.3.2. Research and demonstration projects
3.3.3. Future prospects
Chapter 4. Design of RC Structures Reinforced with FRP Bars
4.1. Design Philosophy
4.1.1. Design material properties
4.1.2. Flexural design philosophy
4.1.3. Nominal flexural capacity
4.1.4. Strength reduction factor for flexure (f)
4.1.5. Check for minimum FRP reinforcement
4.1.6. Serviceability
4.2. Shear
4.2.1. Shear design philosophy
4.2.2. Shear failure modes
4.2.3. Minimum shear reinforcement
4.2.4. Shear failure due to crushing of the web
4.2.5. Detailing of shear stirrups
4.2.6. Punching shear strength of FRP reinforced, two-way concrete slab
4.3. ISIS Canada Design Approach for Flexure
4.3.1. Flexural strength
4.3.2. Serviceability
4.4. Design Approach for CFRP Prestressed Concrete Bridge Beams
4.4.1. Theoretical development of design equations
4.4.2 Deflection and stesses under service load condition
4.4.3. Nonlinear response
E4.1. Design Example 1
E4.2. Design Example 2
E4.3. Design Example 3
E4.4. Design Example 4: A Case Study Problem
E4.5. Design Example 5: Case Study of CFRP Prestressed Concrete Double-T Beam
E4.6. Design Example 6: Case Study of CFRP Prestressed Concrete Box-Beam
E4.7. Design Example
Chapter 5. Design Philosophy for FRP External Strengthening Systems
5.1. Introduction
5.1.1. Non-prestressed soffit plates
5.1.2. End anchorage for unstressed (non-prestressed) plates
5.1.3. Prestressed soffit plates
5.2. Flexural Failure Modes and Typical Behavior
5.2.1. Flexural failure
5.2.2. Shear failure
5.2.3. Plate-end debonding failures
5.2.4. Plate-end interfacial debonding
5.2.5. Intermediate crack-induced interfacial debonding
5.2.6. Other debonding failures
5.2.7. Some additional aspects of debonding
5.3. Flexural Design Considerations
5.3.1. Flexural design philosophy (ACI 440-2R-02)
5.3.2. Strengthening limits
5.4. Design Material Properties
5.5. General Considerations for Flexural Strengthening
5.5.1. Assumptions
5.5.2. Section shear strength
5.5.3. Existing substrate strain
5.6. Nominal Strength, Mn
5.6.1. Controlling failure modes
5.6.2. Strain level in FRP reinforcement
5.6.3. Stress level in the FRP reinforcement
5.7. Ductility
5.8. Serviceability
5.9. Creep-Rupture and Fatigue Stress Limits
5.10. Applications of Flexural Design Considerations to a Singly Reinforced Rectangular Section
5.10.1. Ultimate flexural strength
5.10.2. Stress in steel under service loads
5.10.3. Stress in FRP under service loads
5.11. Shear Strengthening
5.11.1. Nominal shear strength (ACI 440.2R-02)
5.11.2. Shear strength contribution of FRP system
5.12. Spacing of FRP Strips
5.13. Reinforcement Limits
5.14. Design Procedure for Strengthening of RC Beam Using NSM Bars
5.14.1. Flexural strengthening
5.14.2. Design procedure for flexural strengthening using NSM FRP rebars
5.14.3. Shear strengthening
5.14.4. Anchorage length requirement
5.15. ACI 440.2R-02 Design Approach for NSM FRP Strengthening
5.15.1. Flexural design approach
5.15.2. Nominal flexural strength
5.16. Design for Shear Strength
5.16.1. Ultimate shear strength
5.17. Serviceability
5.18. Detailing
5.19. Development Length of NSM FRP Bars
5.20. ISIS Canada Design Approach for External FRP Strengthening
5.20.1. Flexural strengthening of beam and one-way slab
5.20.2. Flexural design approach
5.21. ISIS Canada Design Guidelines for Shear Strengthening
5.21.1. Design principles
5.22. External Strengthening of Columns
5.22.1. Slenderness limits of circular columns
5.22.2. Confinement
5.23. Fundamentals of Seismic Retrofit of Columns
5.23.1. Potential failure modes
5.23.2. Flexural ductility of retrofitted columns
5.23.3. Shear strength contributions
5.23.4. Flexural plastic hinge confinement
5.23.5. Lap splice clamping
E5.1. Design Example 1
E5.2. Design Example 2
E5.3. Design Example 3: Shear Strengthening Using CFRP Laminates—A Case Study
E5.4. Design Example 4: A Case Study Problem
E5.5. Design Example 5
E5.6. Design Example 6
E5.7. Design Example 7
E5.8. Design Example 8
E5.9. Design Example 9
E5.10. Design Example 10
E5.11. Design Example 11
E5.12. Design Example 12
E5.13. Design Example 13
E5.14. Design Example 14
E5.15. Design Example 15: Shear Strengthening as per ISIS Canada Design Approach
Chapter 6. Durability-Based Design Approach for External FRP Strengthening of RC Beams
6.1. Designing of Reinforced Concrete Beams
6.1.1. Compute design material properties
6.1.2. Compute the existing substrate strain
6.1.3. Compute the balanced plate ratio (ρf, b)
6.1.4. Compute the maximum allowable plate ratio (ρf, max)
6.1.5. Proportion of the FRP plate
6.1.6. Compute the balanced plate ratio (ρf, bb) to determine failure modes
6.1.7. Determine the critical plate ratio (ρf, c)
6.1.8. Determine the mode of failure
6.1.9. Nominal moment capacity of strengthened beams
6.1.10. Compute design moment capacity
6.1.11. Allowable services stresses
E6.1. Design Example 1: A Case Study Problem
E6.2. Design Example 2: A Case Study Problem
E6.3. Design Example 3: A Case Study
Bibliography
Index